收藏本站
Figure 2
5. Insert the die retaining screw through the
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full crimping.
The tool frame holds a die assembly with three
crimping chambers. The die assembly features an
upper die and a lower die. Die retaining screws are
used to position and secure the dies in the tool frame.
moving jaw and through the die. Tighten the screw
just enough to hold the die in place. Do not tighten
the screw completely at this time.
6. Carefully close the tool handles, making sure
that the anvils and indenters align properly.
Continue closing the tool handles until the ratchet
has engaged sufficiently to hold the dies in place,
then tighten both die retaining screws.
7. To disassemble, open the tool handles until the
ratchet releases, remove the two die retaining
screws, and slide the dies out of the tool jaws.
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the upper die in the stationary jaw of the
tool frame so that the largest indenter is facing
inward. See Figure 2.
3. Insert the die retaining screw through the
stationary jaw and through the die. Tighten the
screw just enough to hold the die in place. Do not
tighten the screw completely at this time.
4. Place the lower die in the moving jaw of the tool
frame so that the largest anvil is facing inward. See
Figure 2.
Refer to Figure 1 and select wire of the specified size
and insulation diameter. Strip the wire to the length
indicated, taking care not to nick or cut wire strands.
Select an applicable splice and identify the
appropriate crimping chamber according to the wire
size markings on the dies. Refer to Figure 3 and
proceed as follows:
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
FCP22N60N MOSFET N-CH 600V 22A TO-220
P51-75-A-AF-D-5V-000-000 SENSOR 75PSI 9/16-18 UNF 1-5V
P51-50-A-AF-D-5V-000-000 SENSOR 50PSI 9/16-18 UNF 1-5V
P51-75-A-AD-D-5V-000-000 SENSOR 75PSI 7/16-20 UNF 1-5V
P51-75-A-AA-D-5V-000-000 SENSOR 75PSI 7/16-20 UNF 1-5V
P51-50-A-AA-D-5V-000-000 SENSOR 50PSI 7/16-20 UNF 1-5V
P51-750-A-Z-D-5V-000-000 SENSOR 750PSI 1/4-18 NPT 1-5V
P51-500-A-Z-D-5V-000-000 SENSOR 500PSI 1/4-18 NPT 1-5V
相关代理商/技术参数
58547 制造商:Brady Corporation 功能描述:
58548-1 功能描述:折皱器 PRO-CRIMPER W/DIE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper
58548-2 功能描述:冲压机与冲模 DIE ASSEMBLY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能:
585-48-3 制造商:Fox Electronics 功能描述:SMD,3.2X2.5,HCMOS OSC,-40+85,100PPM,3.3V,48.0000 MHZ - Cut Tape Product
5-854830-0 功能描述:折皱器 CRIMPER INSULATION SP(.110 OV) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper
5-854830-1 功能描述:折皱器 CRIMPER, INS SPECIAL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper
5-854830-2 功能描述:折皱器 CRIMPER INSUL. SP. (.160 OV) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper
5-854830-3 功能描述:折皱器 CRIMPER, SPECIAL INS RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper